It is currently Sun Oct 26, 2014 10:28 am



Post new topic Reply to topic  [ 16 posts ]  Go to page Previous  1, 2
Author Message
 Post subject: Re: what is the best way to read a rc receiver output?
PostPosted: Mon Apr 16, 2012 8:47 pm 
Offline

Joined: Fri Jun 03, 2011 7:45 pm
Posts: 121
Location: Central Coast, CA
Hi Jacob,

is the GitHub Zip complete? Looks like the pic32lib has no files, and GPS only has GPS.h. TokenParser has no files, but needs at least TokenParser.h.

19 files?

Maybe I need something else?

Maybe point me to the notes needed to compile?

I am not current on the PIC lib, come to think of it.

Thanks!

Alan KM6VV

_________________
Visit:
http://groups.yahoo.com/group/SherlineCNC/
http://tech.groups.yahoo.com/group/HexapodRobotIK/


Top
 Profile  
 
 Post subject: Re: what is the best way to read a rc receiver output?
PostPosted: Tue Apr 17, 2012 1:34 am 
Offline
User avatar

Joined: Sat May 28, 2011 6:34 am
Posts: 658
Location: Southern California
KM6VV wrote:
Hi Jacob,

is the GitHub Zip complete? Looks like the pic32lib has no files, and GPS only has GPS.h. TokenParser has no files, but needs at least TokenParser.h.

19 files?

Maybe I need something else?

Maybe point me to the notes needed to compile?

I am not current on the PIC lib, come to think of it.


the pic32lib and TokenParsers are submodules so you need to do a submodule update. The gps code is not complete and there is only a header.

If you look at github.com/pontech you should see the submodules. I was able to pull and update the whole project.

Jacob

NOTE: There are a couple of other issues as well that have been fixed in MPIDE to get this to compile, I'll will have to put a readme together.

_________________
PONTECH Quick240 an industrial form factor platform for chipKIT and Arduino users.


Top
 Profile  
 
 Post subject: Re: what is the best way to read a rc receiver output?
PostPosted: Tue Apr 17, 2012 1:48 am 
Offline

Joined: Fri Jun 03, 2011 7:45 pm
Posts: 121
Location: Central Coast, CA
OK, I get it!

Thanks,

Alan KM6VV

_________________
Visit:
http://groups.yahoo.com/group/SherlineCNC/
http://tech.groups.yahoo.com/group/HexapodRobotIK/


Top
 Profile  
 
 Post subject: Re: what is the best way to read a rc receiver output?
PostPosted: Tue May 15, 2012 6:10 am 
Offline

Joined: Thu May 10, 2012 9:08 am
Posts: 5
What voltage are the signals from the RC receiver you are using? I ask because a lot of the PIC32 I/O lines don't seem to be 5 volt tolerant, especially on on the smaller packages like the PIC32MX250F128B etc. I know having built a few multi-copters myself, that RC receivers can have a lot of channels. I have mostly used ATmega chips which run on 5volts, I haven't tried a PIC32 as a flight controller yet, though no doubt will one day.


Top
 Profile  
 
 Post subject: Re: what is the best way to read a rc receiver output?
PostPosted: Tue May 15, 2012 6:39 am 
Offline
User avatar

Joined: Sat May 28, 2011 6:34 am
Posts: 658
Location: Southern California
The UAV100 has buffered inputs.

Jacob

_________________
PONTECH Quick240 an industrial form factor platform for chipKIT and Arduino users.


Top
 Profile  
 
 Post subject: Re: what is the best way to read a rc receiver output?
PostPosted: Mon Nov 19, 2012 11:43 am 
Offline

Joined: Mon Nov 19, 2012 9:21 am
Posts: 59
Location: Bangalore
you can download simple bare program on chipkit32 using mpide IDE 023

you will start receiving data.

ex:

void setup()
{
}
void loop()
{
}

and open serial monitor to view the data

_________________
With Warm Regards

AMPS


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 16 posts ]  Go to page Previous  1, 2

Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Theme designed by stylerbb.net © 2008
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
All times are UTC [ DST ]